Picture of a commercial building.

The greatest cause of failure for a flat roof is the failure to correct minor deterioration and defects, in their early stages. Problems caused by weather or natural disasters, or by age, require roofing contractors and flat roof repair. A contractor will advise the building owner whether to repair or replace and will supervise the implementation of engineering plans, as needed. Flat Roof repair is one of the commonly neglected aspects. Many homeowners tend to realize the importance of flat roof repair only after the roof starts leaking.

Most flat roofs are found on commercial buildings and were probably installed by professional commercial roofers with flat roofing experience; however, you will find some residences with this type of installation. Unfortunately, most of these installs were done by contractors with little or no experience dealing with this type of roofing and end up requiring repair long before reaching the minimum life expectancy of the materials. Here are some of the easy and most common steps you can take when evaluating your roof and determining what type of job is needed to be done.

Simple procedures you can follow when repairing your flat roof at your home.

1. First, ensure that you can sweep all of the dirt and debris off of the surface and look closely at the problem. It is also important to ensure you have a clean surface for roofing cement to stick to properly.

Repairing the damaged section and replacing it with a new section would be ideal for small damaged areas of the roof. Dirt and gravel from the damaged section of the roof should be cleaned by grabbing a broom and sweeping it clean. The gravel should not be discarded and can be used for repairs. The damaged area can be removed by using a straight edged utility knife. You will need to put some effort for cutting a rectangular section of the roofing material. The first layer of equipment needs to be cut first and the other layers that are damaged can be cut after this and this is one of the necessary steps of restoring the roof.

2. Secondly, you want to cut around any areas that are cracked or peeling with a knife that is sharp and remove those bad sections. Sometimes you may have to lift up shingles to evaluate the undersides because problems may not be obvious when they are small. By making your shapes uniform squares or rectangles, you can keep them uniform and easier to replace with new materials.

Picture of a roofer pressing weld layers of roofing material. Flat roof installation. Heating and melting bitumen roofing felt.

3. Try to take that cut-out piece and use it to measure a new piece of shingle or roofing material to replace the broken area. You will want to ensure that cement or putty around the edges is adequate to keep a watertight seal. Flat tops on buildings are prone to standing water due to poor drainage, and you shouldn’t allow the water to have a place where it can seep in and cause more damage in the long run. Overtop of the patch a full layer of cement seal should ensure all edges are accounted for and tightened down.

4. A replacement that is 4 inches larger than the first replacement needs to be cut and the first patch must be overlapped by this by at least 2 inches on each side. Roofing cement can be used to cover the first replacement patch, and you must extend it by at least 3 inches outside the patch perimeter. Similar to what you did with the first replacement you would need to press down the second replacement and hold it in place as you cement and nail it.

Picture of a roofer repairing a flat roof drain.

5. Sweep back the gravel onto the top of the patch to help hold it in place after the cement has begun to set in. If the cement has not hardened the wind could easily pick the patch job and blow it away, and you would have to start the repairs all over again.

Keep all of these things in mind when considering the challenges and obstacles of flat roof repair. When in doubt be sure to contact a team of professionals in your area that can be sure the job will be done right the first time. Often trying to attempt a complicated or complex job can result in more difficulties in the long run and may even end up costing a lot more money. Get the job done right by consulting a professional with expertise and experience today. Remember, flat roofs often require regular maintenance by cleaning the debris that may build up and clog roof drainage.

Picture of a couple installing thermal insulation thru glass wool on their roof, they are looking pretty proud.

The vast majority of people are under-informed when it comes to the topic of attic ventilation. Sure, it’s not the most intriguing opening line at parties, but proper ventilation of attic can add more years to the life of the roof, can improve the efficiency of the home, and may improve your health. Typically your local roofing company should be able to provide you with proper attic insulation. Now, there is some precision measure required in gauging the amount of the ventilation your attic requires. As with the HVAC unit, you need to work with the proportions of your home rather than assuming more is better. If you have very little air circulation in the attic, you will waste energy cooling your home in the summer; in cooler weather, poor ventilation can result from more than moisture, which could lead to mold. More than 10 percent of people have the allergy to mold, so you home could make sick. Therefore, the best strategy is to speak to a roofing expert to avoid your attic be the source of problems for your home.

Picture of a roof vent.

Another common misconception about the attic ventilation is that it is strictly a concern in warm weather. While proper air circulation is important to your home’s efficiency, attic ventilation works properly in tandem with insulation, thermal barriers, and roofing materials. The truth is, it is the cool weather which poses the greatest risk to poorly ventilated attics. Roof vents do not, as many people believe, allow warmth to escape during the winter. They do, however, help eliminate the damp air that can cause damage to our insulation, and to the usually unfinished wood surfaces in the attic. If this problem goes unaddressed too long, you could have a dangerous and expensive problem on your hands.

The humidity in a home can be a big factor which affects your health. An environment which is too humid can be the cause of allergies breaking out or lung disease and related problems. You can easily avoid all these inconveniences if you have a good attic ventilation system installed.

If your attic is properly ventilated, then it would be a great help since the circulation that a ventilator promotes would make sure that hot air is expunged from a home during summers, and that moisture would also be kept out during winters as well.

While it is good to do your research on the type and amount of ventilation your attic may need, the best thing to do is to find a roofer inspector who has the knowledge your particular climate, and the types of ventilation that work best in your area. Even if you have roof, vents, it is worth it to have them checked. They may not be put up a performance for a variety of reasons, and a professional can diagnose any such problems and recommend a solution.

Picture of a metal roof vent.

Importance

Many people would agree that the importance of attic ventilation is to improve energy efficiency during every season; however, there are other ways to improve energy efficiency other than this, such as insulation and roofing material that are designed to maximize energy performance. The application of an attic vent to thwart moisture build-up provides the greatest advantage to houses located in colder climates.

Where there is intense cold weather, it will be more beneficial to have these circulation systems to avert the formation of condensation on sheathing material and avoid dampness on other major components. It will help put a stop to any serious problems from developing in both the summer and winter.

Benefits

The benefits of a proper ventilation system could prevent all of these problems. Proper air circulation provides a comfortable living environment, decreases energy costs, ensures the welfare of household members, and could even decrease or eliminate the need for expensive repairs and maintenance.

The importance, function, and benefits of a good ventilation system should not be overlooked since they are engineered to eradicate moisture build-up by managing attic air circulation. While a good air circulation system is essential to help reduce utility bills and ensure that a home stays in good condition, it also helps to keep a home safe by avoiding structural damage or premature failure of the roofing structure. Therefore, to maintain efficiency in an overall building structure, adequate roofing ventilation is a must!

Picture of a water tank softener.

Water, long acknowledged as the purest of elements, has become a little scary in the last few decades. Most people don’t feel comfortable drinking straight from the tap any longer. One of the most popular solutions for many homes is a water softener. But how do you know how to choose the right water softener? Star Plumbing Company out of Mt. Juliet Tennessee offered post article for you about popular water softener questions. Here is a step by step guide to get you on the right track.

 

Step 1 – Test the Amount of Hardness to your Water
Your first step should be to figure out just how hard your water is. Water softeners work by removing elements like calcium and magnesium, so you need to know just how much of these elements you’re dealing with and how powerful a system you’ll need.

If you’ve noticed that you have a hard time lathering soap or shampoo, you most likely have hard water. You can purchase a water testing kit and run the test yourself or hire a professional to come by and assess your water.

Read More →

Picture of a water softener

 

This article is going cover the benefits of installing a soft water system in your house. Star Plumbing, a Mt. Juliet plumbing company is going to guide us through the benefits of installing a soft water system.

Do you have hard water in your house? Hard water is water that contains calcium and magnesium in high level. It creates some problems in your house like clogging the pipe, doing more work by boiling it, and many more. When you boil the water, more energy will be used and it is a waste of time and money. Thus, you need soft water system to remove the minerals than can cause your water to be hard.

Read More →

Considering the greater part of the twists and joining streams in a home’s waste lines. It’s not astonishing that drain pipes periodically obstruct. Luckily, many blockages can be cleared with a couple of modest tools. To abstain from doing hurt, you have to pick the correct tool, evade basic slip-ups and know when to call a drain cleaning administration or authorized handyman.
Fundamental Tools Read More →

Roofer installing clay tiles

It is important that the roof over your head is dependable. You should know what materials your roof is made of. Most people have no clue of what materials are suitable for their roof. It is important that you have an idea of what type of roofing material is best for Read More →

roof repairs and installations

Antioch Roofing & Repairs, a roofing company in Antioch, TN have guided this article with real life insights. Installing a new roof and repairing an existing roof are the only two options available for any building and the difference between both the methods is the cost difference. Installing a new one costs more while repairing is done easily. The cost can fluctuate based on the following factors:

Read More →

roofer installing shingles

First, it should be well known that not all rooftops are made the same, and not all roofers charge similar costs. Contingent upon the sort of your roof, geographic area, and the organization or end of the week warrior you employ, the aggregate introduced cost of a composition shingles rooftop could shift between $2.70 to $7.55 per square foot introduced. — That’s anywhere in the range of $275 for a cheap offer, (for example, an offer from an end of the week warrior or tempest chaser who works with no risk protection and does not have any laborer’s comp.) to $750 per square for a completely warrantied work finished by a top of the line outside renovating organization. A square is equivalent to 100 square feet. A standard rooftop size is around 1,700 square feet.

Read More →